Jeep Commander Workshop Manuals and Repair Manuals

Every Manual available online - found by our community and shared for FREE. Enjoy!

Jeep Commander

The Jeep Commander (XK) is a mid-size SUV produced by the Jeep division of the American manufacturer Chrysler, from 2006 to 2010. The Jeep Commander was first introduced at the 2005 New York Auto Show. It was produced as a 5 or 7-passenger counterpart to the third generation Jeep Grand Cherokee, with the initial inspiration coming from the Jeep Grand Wagoneer. Standard features included: electronic stability control, traction control, electronic roll mitigation, back up sensors, immobiliser, front dual-stage and side curtain airbags, TPMS, power heated mirrors, remote keyless entry, automatic headlights, UConnect infotainment system and a full-size spare wheel. The Jeep Commander was discontinued after the 2010 model year.

Jeep Commander FAQ's

How do I change a cabin air filter in a Jeep Commander?

To change a cabin air filter in a Jeep Commander, start by locating the cabin air filter housing, which is typically located behind the glove compartment. Open the glove compartment and remove any contents, then push in on the sides of the compartment to release it and allow it to swing down. Locate the access panel to the cabin air filter housing and remove it by pressing the tabs or turning the locking mechanism. Slide out the old filter and replace it with a new one, making sure it is properly aligned. Reinstall the access panel and the glove compartment.

How do I change a serpentine belt in a Jeep Commander?

To change a serpentine belt in a Jeep Commander, start by locating the belt tensioner, which is typically a spring-loaded pulley. Use a wrench or a specialized tool to rotate the tensioner and release tension on the belt. With the tension released, carefully slide the belt off the pulleys and remember the routing pattern for installation. Install the new belt by following the same routing pattern and again rotating the tensioner to provide slack for the belt. Ensure the belt is properly seated on all pulleys before releasing the tensioner.

How do I change the oil in a Jeep Commander?

To change the oil in a Jeep Commander, start by locating the oil drain plug underneath the vehicle and removing it with a wrench. Allow the old oil to fully drain out before replacing the drain plug. Next, remove the old oil filter and install a new one, making sure to lubricate the gasket with a bit of fresh oil. Finally, refill the engine with the recommended amount of new oil, checking the level with the dipstick to ensure it is at the proper level.

How do I check and top up the engine coolant in a Jeep Commander?

To check and top up the engine coolant in a Jeep Commander, start by allowing the engine to cool down completely. Locate the coolant reservoir, which is typically a translucent plastic tank, and check the fluid level against the markings on the side of the reservoir. If the coolant level is low, remove the cap and add the recommended coolant mixture slowly to the "full" or "max" line. It is important to use the correct type of coolant mixture as specified in the owner's manual to maintain proper cooling system function. Finally, reinstall the cap securely before closing the hood.

How do I replace a brake pad in a Jeep Commander?

To replace a brake pad in a Jeep Commander, start by safely lifting the vehicle and removing the wheel to access the brake caliper. Use a wrench or socket to remove the caliper bolts and then carefully lift the caliper off the rotor. Slide out the old brake pad from the caliper bracket and install the new one, making sure it is properly aligned. Before reassembling, it is recommended to inspect the brake rotor and consider resurfacing or replacing it if necessary. Finally, reinstall the caliper, tighten the bolts, and repeat the process for the other brake pad.

How do I replace a headlight bulb in a Jeep Commander?

To replace a headlight bulb in a Jeep Commander, start by accessing the headlight assembly from the engine compartment. Locate the back of the headlight and disconnect the wiring harness by pressing the release tab and pulling it off. Then, twist the bulb socket counterclockwise to remove it from the assembly. Replace the old bulb with a new one, making sure not to touch the glass part with bare hands. Finally, reinsert the bulb socket into the headlight assembly, twist it clockwise to secure it, and reconnect the wiring harness.

How do I replace a windshield wiper blade in a Jeep Commander?

To replace a windshield wiper blade in a Jeep Commander, start by lifting the wiper arm away from the windshield. Locate the release tab or button on the wiper blade connector and press or push it to release the old blade. Slide the old blade off the wiper arm and discard it. Align the new wiper blade connector with the wiper arm and firmly press it until it clicks into place. Finally, carefully lower the wiper arm back onto the windshield and repeat the process for the other wiper blade.

How do I reset the check engine light in a Jeep Commander?

To reset the check engine light in a Jeep Commander, start by ensuring that the underlying issue causing the light to illuminate has been resolved. Once the issue is fixed, the light should turn off on its own after a few driving cycles. However, if it persists, you can try resetting the light by disconnecting the vehicle's battery for about 15 minutes. This will reset the vehicle's computer system, including the check engine light. Keep in mind that disconnecting the battery may also reset other settings, such as radio presets or clock time.

How often should I change the air filter in a Jeep Commander?

The frequency of air filter replacement in a Jeep Commander depends on various factors, including driving conditions and the type of air filter being used. As a general guideline, it is recommended to inspect the air filter every 12,000 miles and replace it if it appears dirty or clogged. However, in dusty or off-road environments, more frequent inspections and replacements may be necessary to ensure optimal engine performance and fuel efficiency.

What is the recommended interval for changing the spark plugs in a Jeep Commander?

The recommended interval for changing the spark plugs in a Jeep Commander can vary depending on the specific model and engine type. As a general guideline, it is recommended to inspect and potentially replace the spark plugs every 30,000 to 100,000 miles, depending on the type of spark plugs installed. It is important to refer to the vehicle's owner's manual or consult with a dealership to determine the specific interval and type of spark plugs recommended for your Jeep Commander.

What is the recommended power steering fluid for a Jeep Commander?

The recommended power steering fluid for a Jeep Commander can vary depending on the specific model and year. It is crucial to refer to the vehicle's owner's manual or consult with a dealership to ensure the correct power steering fluid is used. Using the wrong type or grade of power steering fluid can lead to decreased steering performance, increased wear on the power steering components, or potential fluid leaks. Following the manufacturer's recommendations is essential to maintain optimal power steering function.

What is the recommended tire pressure for a Jeep Commander?

The recommended tire pressure for a Jeep Commander can vary depending on the specific model and tire size. However, a general guideline is to follow the manufacturer's recommendations, which can typically be found on a sticker inside the driver's side door jamb or in the owner's manual. It is important to maintain the correct tire pressure to ensure proper handling, fuel efficiency, and tire longevity.

What is the recommended transmission fluid for a Jeep Commander?

The recommended transmission fluid for a Jeep Commander can vary depending on the specific model and transmission type. It is crucial to refer to the vehicle's owner's manual or consult with a dealership to ensure the correct transmission fluid is used. Using the wrong type or grade of transmission fluid can lead to shifting issues, reduced performance, or even damage to the transmission. It is always best to follow the manufacturer's recommendations to maintain optimal transmission function.

What is the towing capacity of a Jeep Commander?

The towing capacity of a Jeep Commander can vary depending on the specific model and engine configuration. Generally, a properly equipped Jeep Commander can tow up to 7,400 pounds. It is important to check the vehicle's owner's manual or consult with a dealership to determine the exact towing capacity for your specific vehicle, as it may differ based on factors such as engine size, transmission, and optional towing packages.

What type of coolant should I use in a Jeep Commander?

For a Jeep Commander, it is important to use the correct type of coolant to ensure proper engine performance and prevent overheating. The recommended coolant for a Jeep Commander is a mixture of ethylene glycol-based antifreeze and distilled water in a 50:50 ratio. This coolant mixture provides adequate protection against freezing in cold temperatures and prevents boiling in hot conditions, helping to maintain optimal engine temperature.

Jeep Commander Manuals Index

Jeep Commander Workshop Manual

Jeep Commander Owners Manual

Jeep Commander Misc Document

Related Models