Mazda 626 Workshop Manuals and Repair Manuals

Every Manual available online - found by our community and shared for FREE. Enjoy!

Mazda 626

The Mazda Capella is a mid-size car that was manufactured by Mazda Motor Corporation from 1970 to 2002. Sold in the Japanese domestic market under the Capella name, the vehicle was also commonly known in other major markets as the Mazda 626. The first Capella was introduced in 1970 and lasted until 1978. The second generation rear-wheel drive Capella was available between October 1978 and 1982, in both sedan and coupé forms. It is manufactured with both diesel and petrol engines, and both manual and automatic transmission styles were available. The final Mazda 626 rolled off the Flat Rock, Michigan assembly plant on August 30, 2002 but in Colombia they were still being produced until 2006.

Mazda 626 FAQ's

How do I bleed the brakes in my Mazda 626?

Bleeding the brakes in your Mazda 626 is essential to ensure proper brake system performance. Start by locating the brake bleeder valve on each brake caliper or wheel cylinder. Attach a clear plastic hose to the bleeder valve and place the other end into a container to collect the brake fluid. With a helper inside the vehicle, slowly press the brake pedal while you open the bleeder valve. As the pedal is pressed, air bubbles and old fluid will be expelled. Close the bleeder valve and repeat the process until clean fluid without air bubbles is observed.

How do I change the air filter in my Mazda 626?

Changing the air filter in your Mazda 626 is a relatively simple task. Start by locating the air filter housing, which is usually a rectangular plastic box in the engine compartment. Open the housing and remove the old air filter. Inspect the new air filter to ensure it is the correct size and orientation, then install it into the housing. Close the housing securely, making sure all clips or fasteners are properly engaged.

How do I change the windshield wiper blades on my Mazda 626?

Changing the windshield wiper blades on your Mazda 626 is a straightforward process. Start by lifting the wiper arm away from the windshield. Locate the release tab or button on the wiper blade assembly and press or slide it to release the old blade. Slide the old blade off the wiper arm and attach the new blade. Ensure it is securely in place, then carefully lower the wiper arm back onto the windshield.

How do I check and adjust the tire pressure in my Mazda 626?

To check and adjust the tire pressure in your Mazda 626, start by obtaining a reliable tire pressure gauge. Remove the valve cap from each tire and firmly press the gauge onto the valve stem. The gauge will display the current tire pressure. If the pressure is below the recommended level, add air until it reaches the proper pressure. Recheck the pressure and adjust as necessary. Repeat this process for all four tires, including the spare.

How do I check the engine oil level in my Mazda 626?

To check the engine oil level in your Mazda 626, start by parking the vehicle on a level surface and allowing the engine to cool down. Open the hood and locate the engine oil dipstick. Pull out the dipstick, wipe it clean, reinsert it fully, and then pull it out again to check the oil level. The oil level should be between the minimum and maximum marks on the dipstick.

How do I check the transmission fluid level in my Mazda 626?

To check the transmission fluid level in your Mazda 626, start by parking the vehicle on a level surface and allowing the engine to idle for a few minutes. Locate the transmission dipstick, which is usually near the back of the engine compartment. Pull out the dipstick, wipe it clean, reinsert it fully, and then pull it out again to check the fluid level. The fluid level should be within the designated range on the dipstick. If it is low, add the recommended transmission fluid through the dipstick tube.

How do I replace a headlight bulb in my Mazda 626?

To replace a headlight bulb in your Mazda 626, start by opening the hood and locating the headlight assembly. Depending on the model year, you may need to remove the headlight assembly or access the bulb through the engine compartment. Disconnect the electrical connector, remove the retaining clip or screws, and carefully pull out the old bulb. Insert the new bulb, secure it in place, reconnect the electrical connector, and test the headlight before closing the hood.

How do I replace the cabin air filter in my Mazda 626?

To replace the cabin air filter in your Mazda 626, start by locating the cabin air filter housing, which is typically located behind the glove compartment or underneath the dashboard. Open the housing and remove the old cabin air filter. Inspect the new filter to ensure it is the correct size and orientation, then install it into the housing. Close the housing securely, ensuring all clips or fasteners are properly engaged.

How do I replace the spark plugs in my Mazda 626?

To replace the spark plugs in your Mazda 626, start by locating the spark plug wires or coils. Disconnect the wires or coils and remove them from the spark plugs. Use a spark plug socket and ratchet to remove the old spark plugs, taking care not to damage the threads. Install the new spark plugs by hand, then tighten them with the spark plug socket and ratchet. Reconnect the spark plug wires or coils in the correct order.

How do I reset the maintenance light in my Mazda 626?

To reset the maintenance light in your Mazda 626, start by turning the ignition switch to the "on" position without starting the engine. Locate the trip/reset button on the instrument cluster and press and hold it until the maintenance light starts flashing. Release the button and then press and hold it again until the light turns off. The maintenance light should now be reset, indicating that the maintenance interval has been acknowledged.

How do I troubleshoot a faulty power window in my Mazda 626?

If you are experiencing issues with a power window in your Mazda 626, there are a few troubleshooting steps you can take. First, check the fuse for the power windows and replace it if necessary. If the fuse is fine, verify that the window lock switch is not engaged. If neither of these steps resolves the issue, it may be a faulty window switch or motor, which would require further inspection and potentially replacement.

How often should I change the engine oil in my Mazda 626?

It is recommended to change the engine oil in your Mazda 626 every 5,000 to 7,500 miles or every six months, whichever comes first. Regular oil changes are crucial to maintain the engine's performance and prolong its lifespan. Following the recommended maintenance schedule in your Mazda 626 automotive repair manual will ensure proper oil change intervals.

What should I do if my Mazda 626's battery is dead?

If your Mazda 626's battery is dead, you can jump-start the vehicle using jumper cables and another vehicle with a charged battery. Position the vehicles close to each other but not touching, turn off both engines, and connect the positive cables to the positive terminals of each battery, followed by the negative cables. Start the engine of the assisting vehicle, let it idle for a few minutes, and then start your Mazda 626. Once the vehicle is running, remove the jumper cables in the reverse order of connection.

What type of coolant should I use for my Mazda 626?

To ensure proper cooling system performance, it is recommended to use a high-quality ethylene glycol-based coolant with a 50/50 mixture of coolant and distilled water. This mixture provides optimal freeze protection and heat transfer properties. Consult your Mazda 626 automotive repair manual for the specific coolant specifications and guidelines.

Mazda 626 Manuals Index

Mazda 626 Workshop Manual

Mazda 626 Owners Manual

Mazda 626 Misc Document

Related Models

Mazda 626 on Amazon

Mazda 626 & MX-6 & Ford Probe: 1993 thru 2002 - All models (Haynes Repair Manual)