Mazda MX-6 Workshop Manuals and Repair Manuals

Every Manual available online - found by our community and shared for FREE. Enjoy!

Mazda MX-6

The Mazda MX-6 was a front-wheel drive sporty coupé produced by Mazda between 1987 and 1997. It was called the Mazda Capella in Japan until 2002 before being renamed Mazda Atenza/Mazda6. First version was a large coupé, based on the Mazda GD platform, and was powered by the I4 Mazda F engines. It used the Mazda G4A-EL 4 speed electronic shift automatic transmission. The MX-6 was produced with two transmission options, a five-speed manual transmission or a four-speed automatic with overdrive. In 1991 Mazda unveiled the new MX6, commonly referred to as the second generation.

Mazda MX-6 FAQ's

How do I change the oil in my Mazda MX-6?

To change the oil in your Mazda MX-6, begin by lifting the front end of the vehicle with a jack, ensuring it is secure. Locate the oil drain plug underneath the engine and place an oil drain pan beneath it. Remove the drain plug, allowing the old oil to drain completely. Once drained, replace the drain plug and remove the oil filter. Install a new oil filter and then refill the engine with the recommended amount and type of oil.

How do I check the transmission fluid level in my Mazda MX-6?

To check the transmission fluid level in your Mazda MX-6, park the vehicle on a level surface and ensure the engine is at operating temperature. Locate the transmission fluid dipstick, which is typically labeled and located near the back of the engine bay. Remove the dipstick, wipe it clean, reinsert it, and then remove it again to check the fluid level. The fluid should be within the designated range on the dipstick. If it is low, add the recommended type and amount of transmission fluid.

How do I replace a blown fuse in my Mazda MX-6?

Begin by locating the fuse box, which is usually found in the engine bay or under the dashboard. Use the diagram on the fuse box cover or in the owner's manual to identify the fuse that corresponds to the component or circuit that is not working. Use a fuse puller or a pair of needle-nose pliers to remove the blown fuse. Replace it with a new fuse of the same amperage rating. Make sure the new fuse is securely in place before testing the component or circuit.

How do I replace a burnt-out headlight bulb in my Mazda MX-6?

To replace a burnt-out headlight bulb in your Mazda MX-6, start by opening the hood and locating the back of the headlight assembly. Remove the electrical connector from the back of the bulb by pressing the release tab and pulling it off. Then, twist the bulb counterclockwise to remove it from the assembly. Install the new bulb by reversing these steps, making sure it is securely in place before reconnecting the electrical connector.

How do I replace a faulty ignition coil in my Mazda MX-6?

Start by disconnecting the negative battery cable to prevent any electrical hazards. Locate the ignition coil, which is typically mounted on the engine. Disconnect the electrical connectors and remove any mounting bolts securing the coil in place. Carefully pull the coil out of its socket. Install the new ignition coil in the same position, ensuring it is fully seated. Reconnect the electrical connectors and tighten the mounting bolts. Finally, reconnect the negative battery cable and test the ignition system.

How do I replace a faulty oxygen sensor in my Mazda MX-6?

Start by locating the oxygen sensor, which is typically mounted on the exhaust manifold or exhaust pipe. Disconnect the electrical connector from the sensor and use an appropriate wrench or socket to remove it. Install the new oxygen sensor in the same position, ensuring it is properly tightened. Reconnect the electrical connector and clear any diagnostic trouble codes using a scan tool or by disconnecting the battery for a few minutes. Test the vehicle to ensure the new sensor is functioning correctly.

How do I replace a malfunctioning power window motor in my Mazda MX-6?

Begin by removing the interior door panel to access the power window motor. Disconnect the electrical connectors from the motor and remove any mounting bolts or screws securing it. Carefully remove the motor from its position. Install the new power window motor in the same location, ensuring it is securely in place. Reconnect the electrical connectors and reattach the door panel. Test the power window to ensure proper operation.

How do I replace a worn-out clutch in my Mazda MX-6?

Replacing a clutch in a Mazda MX-6 is a complex task that requires special tools and expertise. It is recommended to seek the assistance of a qualified mechanic or automotive technician who has experience with clutch replacement. They will be able to remove the transmission, replace the worn-out clutch components, and reinstall the transmission properly to ensure smooth operation.

How do I replace the brake pads on my Mazda MX-6?

Start by loosening the lug nuts on the wheel where you need to replace the brake pads. Lift the Mazda MX-6 using a jack and secure it with jack stands. Remove the lug nuts and the wheel to access the brake caliper. Use a wrench or socket to remove the caliper bolts and lift the caliper off the brake rotor. Replace the old brake pads with the new ones, ensuring they are properly aligned. Reinstall the caliper and wheel, then tighten the lug nuts.

How do I replace the serpentine belt on my Mazda MX-6?

Begin by locating the tensioner pulley, which is usually found near the front of the engine. Use a wrench or socket to rotate the tensioner pulley counterclockwise, releasing tension on the belt. Slide the belt off the pulleys, noting the routing for installation. Install the new serpentine belt by following the correct routing, ensuring it is properly seated on all pulleys. Rotate the tensioner pulley again to create enough tension and slide the belt onto it. Double-check the belt's alignment on all pulleys before starting the engine.

How do I reset the maintenance light on my Mazda MX-6?

To reset the maintenance light on your Mazda MX-6, turn the ignition switch to the "On" position without starting the engine. Press and hold the "Trip" button on the instrument cluster until the maintenance light begins to flash. Release the button, and the light should reset. If this method does not work, consult the owner's manual for specific instructions or contact a Mazda dealership for assistance.

How do I troubleshoot a misfiring engine in my Mazda MX-6?

If your Mazda MX-6 has a misfiring engine, start by checking the spark plugs and ignition wires for any signs of damage or wear. Replace any faulty components as necessary. Inspect the fuel injectors for clogs or leaks and clean or replace them if needed. Check the air intake system for any restrictions or blockages that may be affecting air flow. If the issue persists, it is recommended to have the vehicle diagnosed by a qualified mechanic to identify and address the underlying cause of the misfire.

How do I troubleshoot an overheating issue in my Mazda MX-6?

If your Mazda MX-6 is overheating, start by checking the coolant level in the radiator and reservoir. Ensure that both are filled to the recommended levels. Inspect the radiator cap for any signs of damage or corrosion and replace it if necessary. Check for any visible leaks or blockages in the cooling system, such as a cracked hose or a clogged radiator. If the issue persists, it is recommended to have the vehicle inspected by a qualified mechanic to identify and address the underlying cause of the overheating.

How often should I replace the air filter in my Mazda MX-6?

It is recommended to replace the air filter in your Mazda MX-6 every 12,000 to 15,000 miles or as specified in your owner's manual. However, if you frequently drive in dusty or dirty conditions, it may be necessary to replace it more frequently. A clogged or dirty air filter can restrict airflow to the engine, reducing performance and fuel efficiency.

What type of coolant should I use in my Mazda MX-6?

It is recommended to use a high-quality, ethylene glycol-based coolant that is specifically formulated for Mazda vehicles. Check the owner's manual or the label on the coolant container to ensure that it meets the manufacturer's specifications for your Mazda MX-6. Avoid mixing different types of coolant, as this can lead to cooling system issues.

Mazda MX-6 Manuals Index

Mazda MX-6 Workshop Manual

Mazda MX-6 Misc Document

Related Models

Mazda MX-6 on Amazon

Mazda 626 & MX-6 & Ford Probe: 1993 thru 2002 - All models (Haynes Repair Manual)