Nissan Cherry Workshop Manuals and Repair Manuals

Yes, you can jump-start your Nissan Cherry using another vehicle. Ensure both vehicles are turned off and parked with their handbrakes engaged. Connect the positive (red) jumper cable to the positive terminal of the dead battery, then connect the other end to the positive terminal of the assisting vehicle's battery. Next, connect the negative (black) jumper cable to the negative terminal of the assisting vehicle's battery, and the other end to an unpainted metal surface away from the dead battery. Start the assisting vehicle, wait a few minutes, then start your Nissan Cherry. Remove the cables in reverse order of connection.

To change the oil in your Nissan Cherry, begin by locating the oil drain plug underneath the engine. Use a wrench to loosen and remove the plug, allowing the old oil to drain completely. Once drained, replace the plug and proceed to remove the old oil filter, replacing it with a new one. Finally, refill the engine with the recommended amount and type of oil specified in the owner's manual, ensuring it is at the correct level using the dipstick.

To check the transmission fluid level in your Nissan Cherry, start the engine and let it idle for a few minutes to warm up. Locate the transmission dipstick, usually at the back of the engine bay. With the engine still running, pull out the dipstick, wipe it clean, reinsert it fully, and then pull it out again. Check the fluid level on the dipstick, ensuring it falls within the recommended range indicated on the dipstick or in the owner's manual. If needed, add the appropriate transmission fluid through the dipstick tube, using a funnel if necessary.

To check the tire pressure on your Nissan Cherry, start by locating the tire inflation placard, which is usually found on the driver's side door jamb or inside the fuel filler door. Remove the valve cap from one tire, then firmly press a tire pressure gauge onto the valve stem to obtain a reading. Compare the measured pressure to the recommended pressure specified on the placard. If needed, add or release air using an air compressor or a tire gauge with an integrated pressure release valve. Repeat this process for each tire, including the spare if applicable.

If you suspect a blown fuse in your Nissan Cherry, begin by locating the fuse box, usually found under the dashboard or in the engine bay. Consult the owner's manual or fuse box cover for the specific location and function of the fuse you need to replace. Use a fuse puller or a pair of needle-nose pliers to carefully remove the blown fuse. Replace it with a new fuse of the same amperage rating, ensuring it is securely seated. Test the electrical component associated with the fuse to confirm its functionality.

To replace a headlight bulb in your Nissan Cherry, first, make sure the engine and headlights are turned off. Open the hood and locate the back of the headlight assembly. Carefully disconnect the electrical connector from the bulb, then remove the bulb holder by twisting it counterclockwise. Gently pull out the old bulb and insert the new one, being careful not to touch the glass with bare hands as this can cause premature bulb failure. Reinstall the bulb holder, reconnect the electrical connector, and test the headlight to ensure proper functionality.

To replace the brake pads on your Nissan Cherry, start by securing the vehicle on a level surface and engaging the parking brake. Remove the wheel or wheels on which you intend to replace the brake pads. Locate the brake caliper, held in place by bolts or pins, and remove them using an appropriate tool. Carefully lift the caliper and slide out the old brake pads. Use a C-clamp or piston tool to retract the caliper piston, creating space for the new, thicker brake pads. Install the new pads into the caliper bracket, ensuring they are properly aligned, then reattach the caliper and secure it with the bolts or pins. Repeat this process for each wheel, then reinstall the wheels and test the brake pedal for proper feel and function.

To replace the cabin air filter in your Nissan Cherry, start by locating the filter housing, which is typically located behind the glove compartment or beneath the dashboard. Open the glove compartment and remove any contents, then squeeze the sides of the compartment inward to release the stops and lower it fully. Locate the filter housing cover and remove any screws or clips securing it. Take out the old cabin air filter and replace it with a new one, ensuring it is properly aligned. Reinstall the filter housing cover, raise the glove compartment, and test the air flow to confirm proper installation.

To replace the spark plugs in your Nissan Cherry, begin by locating the spark plug wires or ignition coil packs, depending on the engine configuration. Disconnect the wires or coil packs by firmly pulling them away from the spark plugs. Use a spark plug socket and ratchet to loosen and remove each spark plug. Inspect the new spark plugs for any signs of damage or improper gapping before installing them. Thread the new spark plugs by hand into the cylinder head, then tighten them using the spark plug socket and ratchet until snug. Reconnect the spark plug wires or coil packs, ensuring they are securely attached.

To replace the windshield wipers on your Nissan Cherry, lift the wiper arm away from the windshield until it locks in an upright position. Locate the release tab or button on the wiper blade attachment, and press or slide it to release the old wiper blade. Remove the old blade by pulling it downward, away from the wiper arm. Align the new wiper blade with the arm and slide it into place until it clicks securely. Gently lower the wiper arm back onto the windshield.

To reset the maintenance light on your Nissan Cherry, turn the ignition switch to the "ON" position without starting the engine. Within ten seconds, press and hold the trip odometer reset button until the maintenance light starts flashing. Release the button, then immediately press and hold it again until the maintenance light turns off. The maintenance light should now be reset, indicating that the maintenance interval has been properly acknowledged.

When troubleshooting an engine misfire in your Nissan Cherry, start by checking for any stored trouble codes using an OBD-II scanner. This will provide valuable information to narrow down the cause of the misfire. Inspect the spark plugs, ignition coils, and spark plug wires for any signs of damage or wear, replacing them if necessary. Additionally, check the fuel injectors, air intake system, and engine compression to ensure proper functioning. If the misfire persists, it may be advisable to consult a professional mechanic with specialized diagnostic equipment.

The air filter in your Nissan Cherry should be inspected regularly and replaced every 12,000 to 15,000 miles or as indicated in the maintenance schedule. However, in dusty or polluted environments, it may be necessary to replace the air filter more frequently. A clean air filter ensures proper air flow to the engine, improving fuel efficiency and preventing potential damage to engine components.

For optimal performance and protection, it is recommended to use a high-quality ethylene glycol-based coolant that meets the specifications outlined in the owner's manual. This coolant should be mixed with distilled water in a 50:50 ratio before being added to the cooling system. Avoid using plain water or incompatible coolants, as they can lead to corrosion or reduced cooling efficiency.