Nissan Pulsar Workshop Manuals and Repair Manuals

First, find a safe location and engage the parking brake. Remove the spare tire, jack, and lug wrench from the trunk of your Nissan Pulsar. Loosen the lug nuts on the flat tire, then use the jack to lift the vehicle until the flat tire is off the ground. Remove the lug nuts, replace the flat tire with the spare tire, hand-tighten the lug nuts, lower the vehicle, and then tighten the lug nuts securely.

Open the hood of your Nissan Pulsar and locate the battery. Check for any signs of corrosion or damage on the battery terminals and cables. Use a voltmeter or multimeter to measure the battery voltage. A fully charged battery should read around 12.6 to 12.8 volts. If the voltage is significantly lower or if you experience starting issues, it may be time to replace the battery.

Locate the brake fluid reservoir under the hood of your Nissan Pulsar. The reservoir is typically located near the firewall on the driver's side. Remove the cap and check the fluid level, which should be between the minimum and maximum marks on the reservoir. If the level is low, add the recommended brake fluid specified in the owner's manual.

Park your Nissan Pulsar on a level surface and ensure the engine is cool. Open the hood and locate the coolant reservoir, which is typically a translucent plastic tank near the radiator. Check the coolant level, which should be between the minimum and maximum marks on the reservoir. If the level is low, add the recommended coolant specified in the owner's manual.

First, ensure both vehicles are parked close to each other and turned off. Connect one end of the positive (red) jumper cable to the positive terminal of the dead battery in your Nissan Pulsar. Attach the other end of the positive jumper cable to the positive terminal of the fully charged battery in the other vehicle. Connect one end of the negative (black) jumper cable to the negative terminal of the fully charged battery. Finally, attach the other end of the negative jumper cable to an unpainted metal surface in the engine compartment of your Nissan Pulsar, away from the battery. Start the vehicle with the fully charged battery, then start your Nissan Pulsar.

Open the hood of your Nissan Pulsar and locate the headlight assembly. Disconnect the electrical connector from the back of the headlight bulb. Remove the retaining clip or ring that holds the bulb in place. Carefully remove the old bulb and replace it with a new one. Reinstall the retaining clip or ring, reconnect the electrical connector, and test the headlight to ensure it is working properly.

Locate the cabin air filter housing, which is usually located behind the glove box or under the dashboard on the passenger side of your Nissan Pulsar. Remove the housing cover or panel to access the old cabin air filter. Take note of the filter's orientation and carefully remove it from the housing. Replace the old filter with a new one, ensuring it is properly aligned. Reinstall the housing cover or panel, and you can now enjoy cleaner air inside your vehicle.

Lift the wiper arm away from the windshield until it locks into a raised position. Locate the release tab or button on the wiper blade, then press or slide it to release the blade from the wiper arm. Attach the new wiper blade by sliding it onto the wiper arm until it clicks into place. Gently lower the wiper arm back onto the windshield, and repeat the process for the other wiper blade.

To reset the maintenance light on your Nissan Pulsar, first, make sure the ignition is in the OFF position. Press and hold the trip reset button located on the instrument panel. While holding the button, turn the ignition to the ON position (do not start the engine) and continue holding the button until the maintenance light resets. Release the button, and the maintenance light should be reset.

It is generally recommended to replace the air filter in your Nissan Pulsar every 12,000 to 15,000 miles or once a year, whichever comes first. However, if you drive in dusty or polluted environments, it may be necessary to replace the air filter more frequently. A clogged or dirty air filter can restrict airflow to the engine, leading to reduced performance and fuel efficiency.

The recommended interval for transmission fluid change in a Nissan Pulsar is typically every 30,000 to 60,000 miles. However, it is advisable to consult your vehicle's owner's manual to confirm the specific interval for your model and year. Regularly changing the transmission fluid helps maintain smooth shifting and prolong the lifespan of the transmission.

The recommended interval for spark plug replacement in a Nissan Pulsar is typically every 60,000 to 100,000 miles. However, it is advisable to consult your vehicle's owner's manual to confirm the specific interval for your model and year. Regularly replacing spark plugs ensures proper ignition and combustion, helping to maintain engine performance and fuel efficiency.

The recommended tire pressure for a Nissan Pulsar can vary slightly depending on the specific model and year. However, the general guideline is to maintain a tire pressure of around 32 psi (pounds per square inch) for both front and rear tires. Proper tire pressure helps optimize fuel efficiency, tire wear, and overall handling of your Nissan Pulsar.

The towing capacity of a Nissan Pulsar can vary depending on the engine type, transmission, and other factors. Generally, the towing capacity ranges from 1,000 to 1,500 pounds. It is important to consult the owner's manual or contact a Nissan dealership for the specific towing capacity of your Nissan Pulsar model and year.

For optimum performance, it is recommended to use synthetic oil with a viscosity of 5W-30 for gasoline engines, and 5W-40 for diesel engines. Using the recommended oil ensures proper lubrication and protection for the engine, resulting in improved fuel efficiency and longevity. Be sure to check the owner's manual for any specific oil requirements or recommendations based on your Nissan Pulsar's model and year.