Toyota Auris Workshop Manuals and Repair Manuals

To adjust the headlights on a Toyota Auris, start by parking the vehicle on a level surface facing a wall or garage door. Measure and mark a horizontal line on the wall at the same height as the headlights. Measure and mark a vertical line on the wall, aligned with the center of the vehicle. Turn on the headlights and locate the adjustment screws on the headlight assembly. Using a screwdriver, adjust the screws to move the headlights up, down, left,

To change the oil in a Toyota Auris, start by locating the oil drain plug underneath the car and placing a drain pan beneath it. Remove the drain plug using a wrench, allowing the old oil to drain completely. Once drained, replace the drain plug and proceed to remove the oil filter, replacing it with a new one. Finally, refill the engine with the recommended amount and type of oil, checking the oil level using the dipstick to ensure it is at the correct level.

To check the transmission fluid in a Toyota Auris, start by parking the vehicle on a level surface and ensuring the engine is warmed up. Locate the transmission dipstick, usually found near the back of the engine bay. With the engine running and the transmission in Park or Neutral, pull out the dipstick and wipe it clean. Reinsert the dipstick fully, then withdraw it again to check the fluid level. The fluid should be within the designated range on the dipstick. If the level is low, add the recommended type of transmission fluid through the dipstick tube, being cautious not to overfill.

To jump-start a Toyota Auris, start by locating the battery and identifying the positive (+) and negative (-) terminals. Ensure both vehicles are turned off and the parking brakes are engaged. Connect one end of the jumper cables to the positive terminal of the dead battery, then connect the other end to the positive terminal of the booster vehicle's battery. Next, connect one end of the second jumper cable to the negative terminal of the booster vehicle's battery and the other end to a suitable grounding point on the dead vehicle, such as an unpainted metal surface. Start the booster vehicle and let it run for a few minutes, then attempt to start the dead vehicle. Once started, carefully disconnect the jumper cables in the reverse order of connection.

To replace a blown fuse in a Toyota Auris, start by identifying the fuse box location, which is usually found in the engine compartment or under the dashboard. Consult the owner's manual or fuse box cover for the specific fuse diagram. Once located, use a fuse puller or needle-nose pliers to remove the blown fuse. Replace it with a new fuse of the same amperage rating, making sure it is securely seated in the fuse box. Finally, test the corresponding component to ensure it is functioning properly.

To replace a burnt-out headlight bulb in a Toyota Auris, start by opening the hood and locating the back of the headlight assembly. Depending on the specific model year, you may need to remove the dust cover or unplug the electrical connector before accessing the bulb. Twist the bulb socket counterclockwise to remove it from the headlight assembly, then pull out the old bulb. Insert the new bulb into the socket, being careful not to touch the glass part with bare hands. Reinstall the socket into the headlight assembly, ensuring it is securely fastened. Test the headlight to ensure it is functioning properly before closing the hood.

To replace a cabin air filter in a Toyota Auris, start by locating the cabin air filter housing, which is typically located behind the glove compartment. Open the glove compartment and remove any contents if necessary. Locate the release tabs or screws securing the filter housing, and remove them to access the filter. Slide out the old cabin air filter and discard it. Install the new cabin air filter, ensuring it is properly aligned with the air flow direction indicated on the filter. Reinstall the filter housing and secure it with the release tabs or screws. Close the glove compartment and test the air flow through the vents to ensure proper installation.

To replace a windshield wiper blade on a Toyota Auris, start by lifting the wiper arm away from the windshield until it locks into a raised position. Locate the release tab or button on the wiper blade assembly, then press or slide it to release the old blade. Slide the old blade off the wiper arm and discard it. Align the new wiper blade with the wiper arm, making sure the hook or connector is securely attached. Press the blade firmly until it clicks into place. Gently lower the wiper arm back onto the windshield. Repeat the process for the other wiper blade if necessary.

To replace the brake pads on a Toyota Auris, start by loosening the lug nuts on the front wheels, then raise and support the vehicle using a jack and jack stands. Remove the lug nuts and wheels, exposing the brake caliper and rotor. Use a brake caliper piston tool or a C-clamp to compress the caliper piston, allowing for clearance to remove the old brake pads. Once compressed, remove the retaining clips or pins securing the brake pads and slide them out. Install the new brake pads, ensuring they are properly aligned and secured. Reassemble the brake caliper, reinstall the wheels, and tighten the lug nuts. Finally, pump the brake pedal a few times before driving to ensure proper brake operation.

To reset the maintenance light on a Toyota Auris, start by turning the ignition key to the "Off" position. Press and hold the trip meter reset button, then turn the ignition key to the "On" position without starting the engine. Continue holding the trip meter reset button until the maintenance light starts flashing, then release the button. Start the engine and confirm that the maintenance light has turned off. The maintenance light should now be reset and will come on again at the appropriate mileage interval for the next scheduled maintenance.

The engine air filter in a Toyota Auris should generally be replaced every 15,000 to 30,000 miles or as recommended in the owner's manual. However, this interval may vary depending on driving conditions and the environment in which the vehicle is operated. It is important to visually inspect the condition of the air filter regularly and replace it if it appears dirty or clogged. A dirty air filter can restrict airflow to the engine, leading to reduced performance and fuel efficiency.

If you have a flat tire on your Toyota Auris, the first step is to safely pull over to the side of the road and engage the parking brake. Locate the spare tire, jack, and lug wrench in the trunk. Position the jack under the designated lifting point and raise the vehicle until the flat tire is off the ground. Loosen the lug nuts with the lug wrench and remove the flat tire. Mount the spare tire onto the wheel studs and hand-tighten the lug nuts. Lower the vehicle, then use the lug wrench to fully tighten the lug nuts in a star pattern. Double-check the lug nuts for tightness before driving.

If your Toyota Auris is overheating, the first step is to turn off the air conditioning and turn on the heater to its highest setting. This will help dissipate some of the heat from the engine. Next, pull over to a safe location and turn off the engine. Allow the engine to cool down completely before attempting to open the hood. Once cooled, check the coolant level and add more if necessary. If the issue persists, it is recommended to consult a professional mechanic for further diagnosis and repair.