Vauxhall Vivaro Workshop Manuals and Repair Manuals

To check the brake fluid level in your Vauxhall Vivaro, locate the brake fluid reservoir under the hood. The reservoir is typically located near the firewall, on the driver's side of the engine compartment. Check the fluid level against the markings on the reservoir, ensuring it is between the minimum and maximum levels. If necessary, top up the brake fluid with the recommended type.

To check the engine oil level in your Vauxhall Vivaro, park the vehicle on a flat surface and make sure the engine is turned off. Locate the oil dipstick, usually located near the engine. Pull out the dipstick, wipe it clean, reinsert it fully, and then pull it out again to check the oil level. Ensure that the oil level is between the minimum and maximum markers on the dipstick.

To check the transmission fluid level in your Vauxhall Vivaro, start the engine and let it idle for a few minutes to warm up. Locate the transmission dipstick, usually found near the back of the engine bay. Pull out the dipstick, wipe it clean, reinsert it fully, and then pull it out again to check the fluid level. Ensure that the fluid level is between the minimum and maximum markers on the dipstick. If necessary, add the recommended transmission fluid through the dipstick tube.

To jump-start your Vauxhall Vivaro, you will need a set of jumper cables and a functioning vehicle with a charged battery. Park the vehicles close together but not touching, turn off both engines, and connect the positive (red) jumper cable to the positive terminals of both batteries. Connect the negative (black) cable to the negative terminal of the charged battery and a metal ground point on the dead vehicle. Start the functioning vehicle, then attempt to start the Vauxhall Vivaro. Once started, let both vehicles run for a few minutes before disconnecting the jumper cables in the reverse order.

To replace a blown fuse in your Vauxhall Vivaro, locate the fuse box, which is usually found in the engine compartment or under the dashboard. Open the fuse box cover and locate the fuse corresponding to the failed circuit. Using a fuse puller or needle-nose pliers, gently pull out the blown fuse. Replace it with a new fuse of the same amperage rating. Close the fuse box cover and test the circuit to ensure proper functionality.

To replace a broken side mirror on your Vauxhall Vivaro, start by removing the interior door panel to access the mirror mounting bolts. Disconnect the electrical connector for the mirror, then remove the mounting bolts. Install the new mirror by reversing the removal steps, ensuring proper alignment and secure fastening. Finally, test the mirror's functionality before reinstalling the door panel.

To replace a faulty brake light bulb in your Vauxhall Vivaro, open the rear trunk or cargo door and locate the bulb holder behind the affected brake light lens. Twist the bulb holder counterclockwise to unlock it, then pull it out. Remove the old bulb and replace it with a new one of the same type. Reinstall the bulb holder by twisting it clockwise until it locks in place. Test the brake light before closing the trunk or cargo door.

To replace a faulty spark plug in your Vauxhall Vivaro, start by locating the spark plugs on the engine. Disconnect the spark plug wire or coil pack connector, then remove the old spark plug using a spark plug socket and ratchet. Install the new spark plug, ensuring proper torque and gap specifications. Reconnect the spark plug wire or coil pack connector, and repeat the process for the remaining spark plugs.

To replace a headlight bulb in your Vauxhall Vivaro, open the hood and locate the back of the headlight assembly. Disconnect the electrical connector from the bulb and remove the bulb holder. Replace the old bulb with a new one, ensuring it is the correct type and wattage. Reinstall the bulb holder, reconnect the electrical connector, and test the headlight before closing the hood.

To replace a malfunctioning power window motor in your Vauxhall Vivaro, start by removing the interior door panel to access the motor assembly. Disconnect the electrical connector and remove the mounting bolts securing the motor. Install the new motor by reversing the removal steps, ensuring proper alignment and secure fastening. Test the window's operation before reinstalling the door panel.

To replace a worn serpentine belt in your Vauxhall Vivaro, start by locating the belt routing diagram, usually found on a sticker under the hood or in the vehicle's manual. Use a wrench or tensioner tool to relieve tension on the belt, then slip it off the pulleys. Install the new belt following the correct routing pattern, ensuring it is properly seated on each pulley. Finally, release the tensioner to apply proper tension to the new belt. Inspect the belt for proper alignment and tension before starting the engine.

To reset the service light in your Vauxhall Vivaro, turn on the ignition without starting the engine. Press and hold the trip reset button on the instrument cluster until the service light starts flashing. Release the button, then press and hold it again until the service light resets and turns off. This procedure may vary slightly depending on the specific model and year of your Vivaro.

The engine coolant in your Vauxhall Vivaro should be changed every 2 to 5 years, or as recommended in the vehicle's maintenance schedule. Coolant deteriorates over time and loses its effectiveness in preventing corrosion and maintaining proper engine temperature. Regular coolant changes help ensure optimal engine performance and prevent potential cooling system issues.

It is recommended to replace the air filter in your Vauxhall Vivaro every 15,000 to 30,000 miles or as specified in the vehicle's maintenance schedule. However, if you often drive in dusty or polluted environments, it may be necessary to replace the air filter more frequently. A clogged or dirty air filter can restrict airflow to the engine, leading to reduced performance and fuel efficiency.

The recommended tire pressure for your Vauxhall Vivaro can vary depending on the specific model and tire size. It is important to refer to the vehicle's manual or the tire placard located on the driver's door jamb or inside the fuel filler flap for the correct tire pressure. Proper tire inflation ensures optimal handling, tire longevity, and fuel efficiency.